Keyence CA-DC100 Manuel d'utilisateur télécharger pdf

LED Illumination Controller

CA-DC100

Instruction Manual

For Safe Usage

● Manual Format

This manual uses the following headings to display important safety

information in order to prevent human injury and device damage.

WARNING

Failure to follow the instructions given under this heading may result in

human injury.

CAUTION

Failure to follow the instructions given under this heading may result in

product damage (product failure, etc.).

Note:This heading is used to indicate common errors made by operations

in relation to device operation.

● General precautions

•Verify that this device is operating normally in terms of functionality

and performance before the start of work and when operating the

device.

• Implement safety measures as necessary to protect against possible

damage that may result in the event that this product fails.

• Proceed with care when modifying or disassembling the CA-DC100,

or when using it in a manner that falls outside of the ranges indicated

in its specifications, since KEYENCE is unable to guarantee device

functionality or performance in such situations.

• Use this product in combination with other devices only after careful

consideration, since the CA-DC100 may fail to satisfy its functionality

and performance capabilities as a result of the conditions and

environment in which it is used.

•Do not use the CA-DC100 with the purpose of protecting human

beings.

*We make every effort to ensure products reach our customers

without any damage. However, if you encounter any defective,

damaged, or missing parts, please contact your nearest KEYENCE

sales office (listed at the end of this manual).

WARNING

Tu rn off the device immediately in any of the following situations:

• When there is a foreign object or liquid such as water, oil, or a chemical

agent inside the device.

• When the device has been subject to excessive mechanical shock or

when the case has been damaged.

•When the controller emits smoke, an unusual smell, or a strange noise.

Continuing to operate the device despite such a problem may

result in fire, electrical shock, or device failure. Contact your

nearest KEYENCE sales office for repairs.

Proper Controller Operation

● Power

WARNING

Do not use the controller with anything other than a 24 VDC power supply.

Doing so may result in fire, electrical shock, or device failure.

Note:Always ground the frame ground terminal or the ground terminal

when using a switching regulator. KEYENCE recommends the use

of separate power supplies in this situation.

● Installation location

Avoid locations such as the following when installing the CA-DC100:

CAUTION

• Locations where the controller is exposed to direct sunlight.

• Locations where the ambient temperature range exceeds 0 to +45

Locations prone to rapid temperature changes.

• Locations with poor ventilation.

• Locations where relative humidity exceeds 35 to 85% RH. Locations

subject to condensation.

• Locations where corrosive or flammable gasses are present.

• Locations where there is excessive dust, salt, or iron powder.

• Locations where the controller is exposed to splashes of substances

such as water, oil, or chemical agents.

• Locations where the controller is subject to direct vibrations or

mechanical shocks.

• Locations where the controller may be influenced by radiation noise or

static electricity.

• Separate the controller’s cables as far as possible from high-voltage

lines and power lines. Interference from such lines may result in non-

standard operation or device failure.

● Handling

WARNING

•Avoid touching the controller during or immediately after use, since it

may become hot at these times. Doing so may result in burn injuries.

• Do not operate the unit after disassembling or modifying it. Doing so

may result in fire, electrical shock, or device failure.

• Do not look directly at the LED for extended periods of time. Doing so

may cause harm to your eyes.

CAUTION

• When connecting and disconnecting cables, always switch off the power

to the controller and any other devices connected to it. Failure to do so

may result in damage to the controller or to other connected hardware.

• When the controller becomes excessively dirty, apply a weak, neutral

detergent to a cloth and wipe away the dirt, then wipe the unit dry with

a soft cloth. Do not use benzene, thinners, or alcohol to clean the

controller. Doing so may result in the discoloration or deformation of

the controller case.

Installation

CAUTION

• Neither the cables attached to the LED illumination area nor extension

cables (sold separately) are flexible, so they are not suitable for

installation on moving parts where the cables must bear a load.

• Extension of the cable between the illumination and the controller will

result in decreased light quantity as a result of lowered voltage. Verify

adequate light quantity before use.

• Do not use this controller in combination with a non-KEYENCE LED

illumination device. Doing so may result in device failure.

Installation method 1

The controller may be attached to a DIN track.

When attaching or removing the controller, pull the fastener on the

rear of the controller in the direction indicated by the arrow.

Installation method 2

You can also use the mounting bracket (sold separately) to install

the controller. In this case use the screws that are provided on the

controller.

Mounting brackets (sold separately)

OP-42168 OP-42169 OP-42170

(Front-mounting) (Bottom-mounting) (Side-mounting)

● Installation orientation

CAUTION

Do not install the controller in an orientation other than one of the 3

shown above. Leave a minimum of 20 mm of space on all sides of the

controller, and use caution when installing any other heat-generating

device (power supplies, etc.) to prevent the ambient temperature from

exceeding +45

Do not use the

screws that come

with the mounting

brackets.

CAUTION

Use these screws

96M0847

1 2

Résumé du contenu

Page 1 - Instruction Manual

1LED Illumination ControllerCA-DC100Instruction ManualFor Safe Usage● Manual FormatThis manual uses the following headings to display important safety

Page 2 - Specifications

2Part Names and Functions1. Power limiter switch (default setting: NORM)NORM Limits light adjustment range to 0 to 60% inorder to protect LED element.

Commentaires sur ces manuels

Pas de commentaire

Keyence CA-DC100 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Keyence CA-DC100. KEYENCE CA-DC100 User Manual [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Keyence CA-DC100