Keyence LS-7000 Manuel d'utilisateur Page 145
- Page / 192
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
7-3
Chapter 7 RS-232C
7
■ RS-232C Connection Settings
Make the following environment settings according to the connecting device. For details,
go to the reference pages indicated in the table. Refer to page 5-7 for RS-232C environ-
ment setting details.
External device
NORMAL
OFF
S1/S2
KV-series
(KV mode)
PLC
Reference page
Environment setting item
D-MODE D-SEND
Non-protocol communications with PCs
or PLC link units.
KV <=> LS
(Command transmission
and reception)
KV <= LS
(KV for command
reception only)
Measured Value Output
and Setting Changes
with Commands (Page
7-4)
Output of Measured
Values under External
Synchronous Control
(Page 7-23)
- LS-7000 Series 1
- General precautions 2
- Safety Precautions 3
- ■ Precautions for LED 5
- Ferrite core 6
- OP-31973 6
- About this Manual 7
- Optimum Measurement Methods 8
- Configuration of Manual 9
- LS-7001 Operation Map 10
- Hold function (See page 3-5) 11
- Contents 12
- Chapter 4 Function Settings 13
- Chapter 7 RS-232C 14
- Chapter 8 Specifications 14
- Chapter 9 Troubleshooting 14
- Appendix 14
- Chapter 1 15
- ■ Special Features 16
- ■ Principle of Measurement 16
- System Applications 17
- Package Checks 18
- Chapter 1 Getting Started 19
- Functions and Nomenclature 21
- ■ Control Panel 22
- Mounting and Connection 25
- 2 Mount the measuring head 26
- Mounting the Controller 27
- ■ Mounting to Panel 28
- Connection 31
- ■ Transmitter and Receiver 32
- ■ Power Supply Cable 32
- Supply Stand On and Off 33
- Measurement and 33
- Chapter 2 37
- Set value 38
- Measurement of Pitch 44
- Chapter 3 45
- Chapter 3 Operation Control 46
- Chapter 3 Operation Control 47
- Area Monitor 48
- Hold Function 49
- Automatic Zero Function 50
- Panel Lock Function 51
- Program Changes 52
- Chapter 4 53
- Flow of Program Settings 54
- External I/O 55
- Output Settings 55
- Measuring Mode Settings 55
- Option Settings 55
- ■ Program Initialization 58
- (See page 4-15) 60
- (See page 4-16) 60
- (See page 4-17) 60
- (See page 4-18) 60
- (See page 4-14) 60
- Area Selection 61
- ■ SEG (Segment) 62
- ■ Setting Procedure 64
- DIA (Diameter) 65
- T-EDGE (Top edge) 65
- B-EDGE (Bottom edge) 65
- SEG (Segment) 65
- 6 Press the 69
- Calibration Settings 72
- 5 Press the 77
- Measuring mode 85
- Analog Output Settings 96
- ■ Analog update mode 98
- Comparator Output Setting 99
- (Normally open) 100
- (Normally closed) 100
- 1 Press the 101
- 2 Press the 101
- 4 Press the 101
- Tolerance (LIMIT) Settings 102
- Limit Settings 103
- Hold Value Elimination 104
- 1 Continue pressing the 105
- Chapter 4 Function Settings 107
- 3 Press the 108
- Display Unit 109
- I/O Mode 111
- Chapter 5 115
- Possible Environment Settings 116
- This part changes 118
- ■ Resetting All Programs 120
- ■ RS-232C Settings 121
- ■ Baud Rate 121
- ■ Parity 121
- ■ Stop Bit 122
- ■ Data Length 122
- ■ Data Mode 122
- ■ Data Transmission Mode 123
- The buzzer turns ON 126
- The buzzer turns OFF 126
- Chapter 6 129
- Connector I/O 130
- Terminal block 130
- Chapter 6 I/O Terminals 131
- Chapter 6 I/O Terminals 134
- ZERO Input 6-3, 6-5, 6-6 135
- ■ FUNCTION Output 136
- Electrical Specifications 137
- ■ NPN Open Collector Output 2 138
- ■ Analog Voltage Output 138
- Timing Chart 139
- ■ Sample Hold 2 140
- ■ Self-timing Hold 140
- ■ BCD Output Switching 141
- ■ Minimum Input Period 142
- Chapter 7 143
- Specifications 144
- ■ RS-232C Connection Settings 145
- ■ Environment Settings 146
- Connecting to KV Series 147
- Outline of Command Formats 148
- Measurement Serial Commands 149
- Commands in Detail 150
- ■ Measured Value Output 150
- Chapter 7 RS-232C 151
- Response 153
- Setup Serial Commands 154
- ■ Area Check 156
- ■ Calculation 156
- ■ Average 156
- (Page 7-15) 161
- Batch Commands 162
- ASCII Table 164
- ■ Output 165
- TIMING input 166
- Sampling period + 3.5 ms 166
- RS-232C data output 166
- Chapter 8 167
- Measuring Head 169
- Optional Accessories 169
- Characteristics 170
- Temperature Characteristics 171
- ■ Measurement Response Time 172
- Mode Specifications 173
- External Dimensions 174
- ■ LS-7030 Measuring Head 175
- ■ LS-7070 Measuring Head 175
- ■ Extension Cable 176
- Chapter 9 177
- Troubleshooting Guide 178
- Chapter 9 Troubleshooting 179
- 2 Continue pressing the 182
- Appendix-2 183
- Appendix-3 183
- Appendix-5 183
- Setting Record Sheet 185
- Threshold 186
- WARRANTIES AND DISCLAIMERS 191
Commentaires sur ces manuels
Produits connexes et manuels pour Capteurs Keyence LS-7000
Capteurs Keyence LS-7600 Manuel d'utilisateur
(220 pages)
(220 pages)
Capteurs Keyence LS-5000 Manuel d'utilisateur
(132 pages)
(132 pages)
Capteurs Keyence DL-CL1 Manuel d'utilisateur
(78 pages)
(78 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
ok
Hello