Keyence IL Series Manuel d'utilisateur télécharger pdf (Page 2)

Setup Functions

 Set the R.V. value to the Shift target value

1. Press the left/right arrow buttons until the sub display shows the

Shift target value.

2. Press the up/down arrow button to change the Shift target value.

3. Press the [ZERO SHIFT] button.

4. The current R.V. value would be set to the Shift target value.

 Set the HIGH and LO tolerance.

1. Press the left/right arrow buttons until the sub display shows the

HIGH/LOW limit setting value.

2. Input the HIGH or LO tolerance by pressing the up/down arrow

buttons.

3. The HIGH and LOW tolerance will be set.

 Setting the Key Lock

1. Press the [MODE] and the up (or down) arrow button for at least 2

seconds.

2. The Key Lock display would appear.

 Canceling the Key Lock

1. When the Key Lock is set, press the MODE and the up (or down)

arrow button for at least 2 seconds.

2. The Key Lock would be cancelled.

 Initializing the sensor

1. Press the SET button 5 times while

pressing the MODE button. The main

display will show “rESET”.

2. Select “YES” by pressing the up/down

arrow button, and press the [MODE]

button. The main display will show

“out”.

3. Select the output polarity from “NPN”

and “PNP” by pressing the up/down

arrow button, and press the [MODE]

button. The main display will show

“AnLG”.

4. Select the analog output from “oFF”,

“0-5V”, “-5-5V”, “1-5V” and “4-20mA” by

pressing the up/down arrow button, and

press the [MODE] button. The sensor

will be initialized.

 Changing the bank (program)

1. Press the up/down arrow button while pressing the [MODE] button.

2. The bank (program) would be switched to another one. Each bank

(program) will have an own HIGH limit setting value/LOW limit

setting value/Shift target value/Analog output upper and lower

range.

Basic setting mode

 How to enter the Basic setting mode

1. Press the [MODE] button for at least 2 seconds.

2. Press the [MODE] or left/right arrow button and select the function

number.

 01 Measurement direction

Set the measurement direction from [Normal] and [Reverse].

[Normal]: The value increases when the target comes close to the

sensor head.

[Reverse]: The value decreases when the target comes close to the

sensor head.

 02 Sampling rate

Set the measurement sampling rate.

 03 Average rate

Set the average rate. High-pass filter and Step count filter can be set

here.

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

HOLD CALC

CHECK

Shift target value

[SHIFT]

lights up.

HIGH tolerance value

[HI]

lights up.

LOW tolerance value

[LO]

lights up.

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

LASER

BANK

R.V.

ANALOG

HI SHIFT

ZERO SHIFT

TIMING

ALIGNMENT

HOLD CALC

CHECK

Performing the initial reset

Output polarity

Analog output

Press ▼ while

holding down the

[MODE] button.

Press ▼ while holding

down the [MODE] button.

Press ▼ while holding

down the [MODE] button.

Press ▼ while holding

down the [MODE] button.

< While Bank 1 is selected>

< While Bank 2 is selected>

< While Bank 3 is selected>

BANK 0 lights

BANK 1 lights

BANK 2 lights

BANK 3 lights

1 2 3

Commentaires sur ces manuels

Pas de commentaire

Keyence IL Series Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Keyence IL Series