Keyence DL-RB1A Manuel d'utilisateur télécharger pdf

BCD Output Unit

DL-RB1A

Instruction Manual

Safety Precautions

 General Cautions

• At startup and during operation, be sure to monitor the functions and

performance of the DL-RB1A.

• Provide appropriate safety measures to avoid any damage in the event

that a problem occurs.

• Do not modify the DL-RB1A or use it in any way other than described

in the specifications. The functions and performance of products used

or modified in this way cannot be assured.

• When the DL-RB1A is used in combination with other instruments, its

functions and performance may be degraded, depending on the

operating conditions and surrounding environment. Use the DL-RB1A

after fully studying the effects of combined use with other instruments.

• Do not use the DL-RB1A for the purpose of protecting the human

body.

• Do not expose the DL-RB1A and peripheral devices to sudden

temperature changes. This may cause condensation, damaging the

equipment.

 Proper environment and conditions

To use the DL-RB1A properly and safely, do not install the DL-RB1A

in locations with the following conditions. Use of this equipment in an

improper environment may cause equipment failure.

•

Locations with high humidity, a large amount of dust, or poor ventilation

• Locations where the temperature rises excessively due to direct

sunlight, etc.

• Locations where corrosive or flammable gas exists

• Locations where the DL-RB1A is directly subjected to vibration or

impact

• Locations where water, oil or chemicals may splash the DL-RB1A

• Locations where static electricity is easily built up

 Noise countermeasures

Installation near a source of noise such as a power source and a

power cable may cause a malfunction or failure in the equipment.

Adopt appropriate countermeasures against noise by using a noise

filter or wiring cables in separate ducts, attaching insulation to the

sensor amplifier or the sensor head, etc.

Package Contents

The product package should include the following items. Check that all

items are included before use.

All possible care was taken in packaging; however, if any parts are found to

be defective or broken, please contact your nearest KEYENCE sales office.

Part Names

WARNING

If the following conditions are encountered,

immediately turn off the power. Continuing to use

the DL-RB1A under abnormal conditions may

cause fire, electric shock or equipment failure.

• When water or foreign matter enters the

controller

• When the DL-RB1A is dropped or the housing is

damaged

• When the DL-RB1A produces smoke or an

abnormal smell

WARNING

• Do not use the DL-RB1A with a voltage other

than specified voltage, as this may cause fire,

electric shock or equipment failure.

• Do not disassemble or modify the DL-RB1A. This

may cause fire or electric shock.

CAUTION

• Be sure to turn off the power to the DL-RB1A and

any connected devices before connecting or

disconnecting the cables. Otherwise, there may

be a risk of damaging the unit.

• Do not turn off the power while setting a

parameter. Otherwise, the settings may be

partially or completely lost.

End unit x 2

OP-26751

Communication unit

DL-RB1A

Expansion connector cover

Switch protection sticker

Alarm indicator (red)

Power indicator (green)

Connector terminal area

Sensor amplifier connector

(for panel mounting type / large display type)*

I/O connector

Sensor amplifier connector

(for DIN rail mounting type)

*Sticker is attached.

Advanced setting switch

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34

1 3 5 7 9 111315171921232527293133

96M10198

1 2 3 4

Résumé du contenu

Page 1 - Instruction Manual

1BCD Output UnitDL-RB1A Instruction ManualSafety Precautions General Cautions• At startup and during operation, be sure to monitor the functions and

Page 2 - Mounting on a DIN rail

2Mounting and connecting Mounting on a DIN rail1Fit the tab of the lower part of the main unit to the DIN rail. While inserting the main unit in the

Page 3 - Output Settings

3Connecting to an External Device How to connectTo connect BCD Output Unit DL-RB1A to an external device, use the connector (MIL connector, female, 3

Page 4 - 10198E 0119-1a 96M10198

4Specification Main unit specification* The number of connectable sensor amplifiers varies depending on the model to be connected.• When configured w

Plus de documents pour Capteurs Keyence DL-RB1A

Voir le document Keyence DL-RB1A Manuel d'utilisateur

Keyence DL-RB1A Manuel d'utilisateur (40 pages)

Commentaires sur ces manuels

Pas de commentaire

Keyence DL-RB1A Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Keyence DL-RB1A. KEYENCE DL-RB1A User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Capteurs Keyence DL-RB1A

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Keyence DL-RB1A